Genie GTH-1056 Telehandler: Specs, Price and Buying Guide

Last updated: October 2026

The Genie GTH-1056 is a 10,000 lb telehandler with a 56 ft 7 in maximum lift height and 42 ft of forward reach. Current models lift 5,000 lb to full height, and the GTH-1056 is one of the most common high-capacity telehandlers in North American rental fleets, so there is a large supply of used units.

This guide covers the GTH-1056’s specs and features, mechanic ratings, how it compares to the JLG 1055 and SkyTrak 10054, what it costs new and used, and what to check before you buy one.

In this guide:

Genie GTH-1056 Specs

SpecificationGenie GTH-1056 (2021 and newer)
Maximum lift capacity10,000 lb
Maximum lift height56 ft 7 in
Capacity at maximum height5,000 lb
Maximum forward reach42 ft
Capacity at maximum reach3,000 lb
Length (without forks)22 ft 6 in
Width8 ft 6 in
Height8 ft 6 in
Wheelbase11 ft 6 in
Ground clearance15 in
Outside turning radius14 ft
Weight31,900 lb
EngineDeutz Tier 4 Final, 74 hp (no DEF) or 121 hp
Transmission3-speed (74 hp) or 4-speed (121 hp) powershift
Travel speed15 mph (74 hp) / 18 mph (121 hp)
DriveFull-time four-wheel drive
Steering modes2-wheel, 4-wheel and crab
Frame leveling10 degrees side to side
Fuel tank30 gal
Tires400/75-28

Specs are from Genie’s current North American spec sheet. Genie redesigned the GTH-1056 for 2021. Earlier units lift 4,000 lb at full height (versus 5,000 lb), reach 56 ft 10 in, weigh about 30,000 lb and may have a John Deere, Perkins or Deutz engine, so check the load chart and engine plate on any used unit.

Genie GTH-1056 telehandler with forks, side view

Key Features

  • 5,000 lb at full height: 2021 and newer units lift half their rated capacity to 56 ft 7 in, which suits placing heavy loads on upper floors and roofs.
  • Two engine choices: a 74 hp Deutz that needs no DEF, or a 121 hp Deutz with more travel speed and drawbar pull.
  • Three steering modes: 2-wheel, 4-wheel coordinated and crab steering for tight sites.
  • Frame leveling: up to 10 degrees side to side for placing loads on uneven ground.
  • Redesigned boom: the 2021 update added a mid-pivot lift cylinder, improved chain retention and slide-in wear pads for easier service.
  • Standard auxiliary hydraulics and quick-attach carriage: run attachments such as buckets, truss booms, swing carriages and fork positioners.
  • Operator aids: a load moment indicator, level indicator, boom angle indicator and rear proximity alarm, with an optional enclosed cab with heat and A/C.
Genie GTH-1056 telehandler climbing a dirt slope on a job site

Mechanic Ratings

Joe N., a mechanic at OHR Rents who services telehandlers in a rental fleet, rated the Genie GTH-1056:

CategoryRating
Overall value4 out of 5
Reliability4 out of 5
Serviceability4 out of 5
Average4 out of 5

How It Compares

The GTH-1056’s closest rivals are the JLG 1055 and SkyTrak 10054, both 10,000 lb telehandlers in the 55 ft class.

SpecificationGenie GTH-1056JLG 1055SkyTrak 10054
Maximum capacity10,000 lb10,000 lb10,000 lb
Maximum lift height56 ft 7 in55 ft53 ft 2 in
Capacity at maximum height5,000 lb5,000 lb4,000 lb
Maximum forward reach42 ft42 ft38 ft 10 in
Capacity at maximum reach3,000 lb3,000 lb3,000 lb
Weight31,900 lb31,559 lbNot published
FleetNow used prices (middle half)$63,900 to $94,900$64,950 to $139,900$61,000 to $128,999
New price (dealer)About $150,000 to $162,000About $185,000Dealer quote

The GTH-1056 has the highest lift height of the three and matches the JLG 1055 for capacity at height and reach, while the SkyTrak 10054 is the most compact. SkyTrak redesigned its telehandlers in 2026, so check the specs for the model year you are buying. The Cat TL1055 is another 10,000 lb, 55 ft class option. See our SkyTrak 10054 guide and JLG vs Genie telehandlers comparison for more.

Need a different size? The Genie GTH-844 lifts 8,000 lb to 44 ft (see our GTH-844 guide), and the Genie GTH-1256 lifts 12,000 lb to about 56 ft. For heavy pick-and-carry work, the Genie GTH-1544 is rated for 15,000 lb.

Pros and Cons

Pros

  • Highest lift height in the 10,000 lb, 55 ft class
  • 5,000 lb capacity at full height on 2021 and newer units
  • DEF-free 74 hp engine option simplifies emissions maintenance
  • Three steering modes and frame leveling for tight, uneven sites
  • Large used supply and common parts in rental fleets

Cons

  • Heavy at about 31,900 lb, which limits trailers and ground conditions
  • Pre-2021 units are rated for only 4,000 lb at full height
  • Many used units are ex-rental machines with 2,000 to 4,000 hours
  • The 121 hp engine requires DEF and aftertreatment maintenance
  • Its 8 ft 6 in width can be tight on narrow job sites

Common Uses

  • Placing trusses, lumber and roofing materials on residential and commercial builds
  • Lifting pallets of block, brick and drywall to upper floors
  • Steel and precast placement with truss booms and jibs
  • Loading and unloading trucks on job sites and in yards
  • Agriculture and industrial material handling with buckets and other attachments

Learn more in our guide to telehandlers and our telehandler vs forklift comparison.

Genie GTH-1056 Price

A new Genie GTH-1056 costs about $150,000 with an open canopy and about $162,000 with an enclosed cab, based on dealer listings for 2025 and 2026 units. Used units cost much less: most GTH-1056 listings on FleetNow are 2012 to 2019 models priced between about $64,000 and $95,000.

Model yearsFleetNow used asking pricesTypical price
2008 to 2015$24,950 to $94,950About $63,900 (20 listings)
2016 to 2019$64,950 to $112,999About $84,850 (15 listings)
2023 to 2025$108,850 to $199,900About $149,950 (5 listings)
2025 and 2026 (new)$149,950 to $161,850Dealer prices

Used prices are FleetNow asking prices from the first 40 Genie GTH-1056 listings in October 2026; typical price is the median. Most listed units show about 1,900 to 4,000 hours. New prices are advertised dealer prices and change often.

What drives the price of a used GTH-1056:

  • Model year: 2021 and newer units have the redesigned boom and 5,000 lb capacity at height.
  • Hours and condition: boom wear, leaks and tire condition have a big effect on value.
  • Cab and options: an enclosed cab with heat and A/C, auxiliary hydraulics and attachments add value.
  • Engine: service records for the engine and, on 121 hp units, the emissions system matter.

What to Check Before Buying a Used Genie GTH-1056

  • Model year and load chart: confirm whether the unit is a pre-2021 or 2021 and newer model, and make sure the correct load charts are in the cab.
  • Boom: extend and retract fully, and check the wear pads, side play, chain slack and any drifting. Look for cracks or welds at the boom, horsehead and pivot.
  • Cylinders and hoses: check the lift, extension, tilt and frame-level cylinders for leaks and damaged chrome.
  • Engine and emissions: check for leaks, hard starting and warning codes. On 121 hp units, ask for DPF and DEF system service records.
  • Transmission and axles: run through every gear in both directions, test the service and parking brakes, and look for leaks at the hubs and differentials.
  • Steering and frame leveling: test all three steering modes and level the frame both ways.
  • Safety systems: test the load moment indicator, alarms, lights and backup alarm.
  • Tires: check for cuts, chunking and uneven wear.
  • Records: ask for service history and the annual inspection, compare the hour meter with the records, and have a Genie dealer check the serial number for open safety bulletins.

Our telehandler inspection checklist covers each item in detail, and the FleetNow Inspect app helps you document a machine’s condition.

Video Review

This product review from Lift and Access magazine walks around the Genie GTH-1056 and its main features.

Shop Genie GTH-1056 Telehandlers With FleetNow

FleetNow lists used Genie GTH-1056 telehandlers from rental companies, dealers and contractors across the country. You can also browse all Genie telehandlers, used telehandlers and Genie equipment.

Have questions about a listing? Contact our team or call 1-216-973-5124. Selling a telehandler? List your equipment on FleetNow.

Genie GTH-1056 FAQs

The Genie GTH-1056 has a maximum lift height of 56 ft 7 in on 2021 and newer units and 56 ft 10 in on earlier units. Its maximum forward reach is 42 ft.

The GTH-1056 has a maximum capacity of 10,000 lb. On 2021 and newer units it lifts 5,000 lb to full height and 3,000 lb at its 42 ft maximum reach. Earlier units are rated for 4,000 lb at full height. Always follow the load chart in the cab.

Genie lists the current GTH-1056 at about 31,900 lb, depending on options. Earlier units weigh about 30,000 lb.

Current units use a Deutz Tier 4 Final engine, either a 74 hp version that needs no DEF or a 121 hp version. Units built before 2021 may have a John Deere, Perkins or Deutz engine, so check the engine plate on a used machine.

On FleetNow, most used GTH-1056 telehandlers are 2012 to 2019 models listed for about $64,000 to $95,000. Newer units cost $108,000 or more, and a new unit costs about $150,000 to $162,000 from dealers. See current GTH-1056 listings.

Most used GTH-1056 telehandlers on FleetNow show about 1,900 to 4,000 hours. Hours matter less than how the machine was maintained, so look closely at boom wear, leaks and service records on any unit over about 4,000 hours.

Both reach about 56 ft. The GTH-1056 is rated for 10,000 lb and the GTH-1256 for 12,000 lb, with more capacity at full height on the GTH-1256. Choose the GTH-1256 if you regularly place heavy loads at height.

August 19th, 2024|Categories: Equipment Essentials, Telehandler|

Share This Story, Choose Your Platform!

Go to Top