Lull 1044C-54 Telehandler: Specs, Price and Buying Guide
Last updated: November 2026
The Lull 1044C-54 is a 10,000 lb, 54 ft telehandler best known for its traverse carriage, which slides the load up to 80 inches left or right at the end of the boom. That lets operators place trusses, wall panels and materials precisely without moving the machine. JLG, which owns the Lull brand, built the 1044C-54 Series II from 2005 until it ended the Lull line in early 2015, so every 1044C-54 you find today is a used machine.
This guide covers the Series II specs, how the traverse works, how it compares to current 10,000 lb telehandlers, used prices, and what to check before you buy one.
In this guide:
Lull 1044C-54 Specs
| Specification | Lull 1044C-54 Series II |
|---|---|
| Rated capacity | 10,000 lb |
| Capacity at max height | 4,000 lb |
| Capacity at max reach | 1,500 lb |
| Max lift height | 54 ft |
| Max forward reach | 45 ft with the carriage traversed (38 ft 6 in retracted) |
| Traverse (side shift of the carriage) | 80 in; capacity drops to 70 percent of the retracted rating when fully traversed |
| Operating weight | 31,350 lb (without carriage or forks) |
| Engine (Series II) | John Deere 4045TF, 115 hp, Tier II |
| Engine (earlier 1044C-54) | Cummins 4BT3.9, 110 hp, with optional John Deere engines |
| Tires | 14.00×24 12-ply (400/75-28 also listed) |
| Width and length | 101 in wide, 246 in long without forks |
| Height and wheelbase | 97 in high, 124 in wheelbase |
| Max travel speed | 22 mph (20 mph on earlier sheets) |
| Fuel tank | 38 gal |
Specs are from JLG’s Lull 1044C-54 Series II spec sheet, with earlier engine and speed figures from the original Lull sheet. Figures vary by year and options, so check the serial plate and load charts on any used machine.
Key Features
- Traverse carriage: the forks slide up to 80 inches side to side at the boom tip, so you can line up a load without repositioning the machine. This is the feature Lull was known for and that current JLG and SkyTrak models do not offer.
- Long reach for its class: 45 ft of forward reach with the carriage traversed, more than many 10,000 lb, 54 to 56 ft telehandlers.
- Rough terrain design: four-wheel drive, large 24 in or 28 in tires and a 22 mph top speed for moving around big sites.
- Older Tier II engines: no diesel particulate filter or DEF system to maintain, though Tier II machines can face restrictions on some job sites and in some states.
Lull History and Model Names
JLG acquired Lull, along with SkyTrak, in the early 2000s and kept selling Lull-branded telehandlers alongside its JLG and SkyTrak lines. In February 2014 JLG announced it would discontinue the Lull line, including the 644E-42, 944E-42 and 1044C-54 Series II, starting in 2015. JLG did not name a direct replacement with a traverse carriage; its JLG and SkyTrak telehandlers cover the same capacity classes.
Lull model names follow a pattern: in the 1044C-54, 10 is the 10,000 lb capacity, 44 most likely refers to four-wheel drive and four-wheel steer, C is the design series, and 54 is the lift height in feet. Sister models include the 944E-42 (9,000 lb, 42 ft) and 644E-42 (6,000 lb, 42 ft).
How the Lull 1044C-54 Compares
| Lull 1044C-54 Series II | JLG 1055 | Genie GTH-1056 | |
|---|---|---|---|
| Rated capacity | 10,000 lb | 10,000 lb | 10,000 lb |
| Max lift height | 54 ft | 55 ft | 56 ft 7 in |
| Max forward reach | 45 ft (traversed) | 42 ft | 42 ft |
| Traverse carriage | Yes, 80 in | No | No |
| Status | Discontinued 2015 | Current | Current |
| Used on FleetNow (Nov 2026) | None listed | See listings | 78 priced listings |
Read more in our guides to the JLG 1055 and Genie GTH-1056, and see JLG telehandlers for the current lineup.
Pros and Cons
Pros
- Traverse carriage for precise load placement without moving the machine
- 45 ft of reach and 54 ft of lift for a 10,000 lb machine
- Used prices well below a new 10,000 lb telehandler
- Simple Tier II engines with no DPF or DEF
Cons
- Discontinued since 2015, so every unit is at least about 10 years old
- Most used units have 4,000 to 8,000 hours or more
- Traverse adds wear points (rails, rollers, cylinder) to inspect
- Tier II engines may not be allowed on some job sites with emissions rules
- Few listings, so finding one can take time
Lull 1044C-54 Price
The 1044C-54 is no longer sold new. Used prices depend heavily on hours, condition and the traverse and boom wear. Recent examples:
| Unit | Price | Type |
|---|---|---|
| 2014, 5,210 hours | $72,997 | Dealer asking price |
| 2012, 5,526 hours | $57,000 | Dealer asking price |
| 2015 | $45,000 | Auction sale, October 2023 |
| 2009 | $17,000 | Auction sale, May 2026 |
| 2001 (Series I), 956 hours | $24,200 | Auction sale, 2022 |
As a rough guide, 2005 to 2015 units have sold for about $17,000 to $45,000 at auction and are listed by dealers at about $45,000 to $73,000. FleetNow had no 1044C-54 listed in November 2026, but had two other Lull telehandlers: a 2011 6.44E-40 with 2,980 hours at $34,000 and a 2006 944E-42 with 5,241 hours at $43,950. See current Lull listings or compare current 10,000 lb machines such as the JLG 1055 and Genie GTH-1056.
What to Check Before Buying a Used Lull 1044C-54
- Hours, records and serial plate: confirm Series I or Series II, the year, engine make and the last annual inspection.
- Traverse carriage: run it fully both ways under load; check the rails and rollers for wear, the traverse cylinder and hoses for leaks, and that the carriage does not drift.
- Boom: check wear pads, extension chains or cylinders, pins and bushings, and look for cracks or weld repairs on the boom and at the pivot.
- Frame leveling and steering: test frame sway and all steering modes.
- Axles and drivetrain: listen for noise from the axles and transmission, and check for leaks at the hubs.
- Engine: check for blow-by, smoke and coolant or oil leaks; confirm whether it is the Cummins or John Deere engine for parts.
- Tires: 14.00×24 tires are expensive, so price replacements in if they are worn or cut.
- Parts: check parts availability and pricing with a JLG dealer before you buy.
See our telehandler inspection checklist and telehandler safety guide.
Video: Lull 1044C-54 Series II Review
This product review from Lift and Access walks through the 1044C-54 Series II and its traverse feature. It is an overview, not a replacement for operator training.
Shop Telehandlers With FleetNow
FleetNow lists more than 1,400 used telehandlers from rental fleets and dealers. Browse used Lull telehandlers, JLG, SkyTrak, Genie or all used telehandlers. New to telehandlers? Start with the ultimate guide to telehandlers.
Looking for a Lull 1044C-54? Contact us or call 1-216-973-5124. Selling one? List your equipment on FleetNow.
Lull 1044C-54 FAQs
The Lull 1044C-54 is rated for 10,000 lb. Capacity drops as the boom extends, to about 4,000 lb at its 54 ft maximum height and about 1,500 lb at maximum reach.
It has a maximum lift height of 54 ft and up to 45 ft of forward reach with the carriage traversed.
The traverse lets the carriage and forks slide side to side at the end of the boom, up to 80 inches on the 1044C-54. Operators use it to fine-tune load placement without moving the whole machine. Capacity is reduced when the carriage is fully traversed.
No. JLG, which owns the Lull brand, discontinued the Lull telehandler line starting in 2015, so all 1044C-54s are used machines.
JLG did not name a direct replacement. Its JLG 1055 and SkyTrak 10054 cover the same 10,000 lb class, but neither has a traverse carriage.
The Series II uses a 115 hp John Deere 4045TF diesel. Earlier 1044C-54 machines used a 110 hp Cummins 4BT3.9, with John Deere engines as an option.
Recent auction sales of 2005 to 2015 units have ranged from about $17,000 to $45,000, and dealers have listed them at about $45,000 to $73,000, depending on hours and condition.
The Series II weighs about 31,350 lb without the carriage and forks.





